HVAC replacement cost in Irving, TX
Irving has two housing stocks in one city: older 1950s–1980s ranch homes in the south and central neighborhoods, where original ductwork and smaller electrical panels are common, and newer master-planned homes around Las Colinas and Valley Ranch. The typical Irving replacement is a 3- to 4-ton split system — central AC paired with a gas furnace — and on older homes the ductwork question matters as much as the equipment.
Estimate My Cost Get Free Irving Quotes
What Irving homeowners pay, by system size
Installed prices for a standard-efficiency split system (AC + furnace or heat pump), including equipment, labor, and permit. High-efficiency systems typically add 15–25%.
| System size | Typical installed range |
|---|---|
| 2-ton system | $6,800 – $10,300 |
| 3-ton system | $8,100 – $12,200 |
| 4-ton system | $9,300 – $14,000 |
| 5-ton system | $10,500 – $15,900 |
Ranges reflect typical Irving single-family homes. Ductwork replacement, electrical panel upgrades, and code-required updates on older homes are extra and should be itemized in any quote.
Permits in Irving
Irving requires a mechanical permit for HVAC system replacement — AC replacement is listed as permitted work with the city. Your installer normally pulls the permit and includes the fee in the quote. In Texas, HVAC contractors are licensed by the state (TDLR), and your contractor should also be registered with the city. Ask to see the permit number on your contract — a contractor who suggests skipping it is a red flag, and an unpermitted install can complicate a future home sale or insurance claim.
Utility incentives in Irving: the Oncor program
Irving homes get their electricity delivered by Oncor (you pick a retail electric provider; Oncor runs the wires). Oncor's Home Energy Efficiency program pays an incentive on qualifying high-efficiency AC and heat pump replacements — but the mechanics surprise people:
- The incentive is paid to your contractor, not to you. Only contractors enrolled as Oncor Participating Service Providers can claim it, and they are expected to pass it through as a discount on your invoice.
- The amount is calculated from your system's modeled energy savings, with per-project caps by size — for 2026, caps run from $2,000 for a 2-ton system up to $3,400 for a 5-ton. Most projects land below the cap.
- Funding is limited and the program runs seasonally, roughly February through mid-November, so a participating contractor's status matters more than the headline number. Ask before you sign, and get the incentive shown as a line item.
Gas furnace bonus: most Irving homes heat with gas from Atmos Energy. Atmos Mid-Tex pays $300 back on an ENERGY STAR gas furnace rated 90% AFUE or higher, or $350 at 95% AFUE and up — worth claiming when you replace the furnace with the AC.
Note: the federal Energy Efficient Home Improvement Credit (Section 25C) ended for equipment installed after December 31, 2025, so don't let a quote count it as a 2026 saving.
Electricity rates: why efficiency pays in Irving
Texas electricity is deregulated in Oncor territory, so your rate depends on the retail plan you choose — typical all-in residential rates in the Dallas area run roughly 14–17¢ per kWh, with advertised plans ranging much wider (always compare at your real usage on the plan's Electricity Facts Label, via the state's Power to Choose site). Air conditioning is the largest single load in an Irving home and can approach half of a summer bill — in an older, leakier home, pairing a right-sized efficient system with duct sealing usually beats buying efficiency tier alone.
Sizing a system for North Texas heat and humidity
Dallas-area design temperatures sit around 100°F, and Gulf humidity means a system also has to remove moisture, not just heat. An oversized unit short-cycles and leaves the house clammy; an undersized one runs flat-out through August. Don't just match the old nameplate: ask for a Manual J load calculation, and on an older Irving home have the contractor inspect duct leakage and return-air sizing while the attic is open — undersized returns are one of the most common comfort complaints in the city's older ranch homes.
The working rule of thumb in North Texas is 1 ton per 500–600 sq ft for typical construction. Use our cost calculator for a first estimate, then insist your installer confirms sizing with a Manual J load calculation. Also note the federal floor: new split systems installed in Texas must be at least 14.3 SEER2 (13.8 SEER2 for systems 45,000 BTU and larger), and split heat pumps at least 14.3 SEER2.
Irving HVAC replacement FAQ
How much does it cost to replace an AC unit in Irving, TX?
Most Irving homeowners pay $8,100–$14,000 installed for a full AC and furnace or heat pump replacement, depending on tonnage and efficiency. A 3-ton standard-efficiency split system typically lands around $8,100–$12,200; older homes needing ductwork or electrical work can run higher.
Does Irving require a permit to replace an AC unit?
Yes. Irving lists AC replacement as permitted work, and a mechanical permit is required. Your TDLR-licensed contractor normally pulls it and includes the fee in the quote — ask for the permit number on your contract.
Can I get an Oncor rebate in Irving?
Irving is Oncor territory, and Oncor's Home Energy Efficiency program pays an incentive on qualifying high-efficiency replacements — but it pays your participating contractor, not you directly, and the contractor applies it as a discount. Ask before you sign whether your contractor participates and get the incentive shown as a line item on the quote.
My Irving home still has its original ductwork. Does it need to be replaced too?
Not always, but it needs to be checked. Many older Irving homes have undersized returns or leaky, deteriorated duct runs that waste a large share of a new system's output. Sealing and insulating ducts is often enough; full replacement is a bigger adder. A good quote inspects the ducts and itemizes duct work separately instead of burying it in the equipment price.
Compare costs in nearby cities
See our other Dallas–Fort Worth guides: Plano, Frisco, Arlington, Garland. Or go back to the national cost overview.
Get free quotes from Irving installers
Tell us about your project and local HVAC partners will contact you with itemized quotes. No obligation.