HVAC replacement cost in Arlington, TX

Arlington's housing stock leans older than the northern suburbs — large numbers of 1960s–1980s ranch and traditional homes in the central and east parts of the city, with newer subdivisions in the south. The typical Arlington replacement is a 3- to 4-ton split system, central AC paired with a gas furnace, and older homes often need a duct and return-air check as part of the job.

Estimate My Cost  Get Free Arlington Quotes

What Arlington homeowners pay, by system size

Installed prices for a standard-efficiency split system (AC + furnace or heat pump), including equipment, labor, and permit. High-efficiency systems typically add 15–25%.

Typical installed cost in Arlington by tonnage
System sizeTypical installed range
2-ton system$6,800 – $10,200
3-ton system$8,000 – $12,100
4-ton system$9,200 – $13,900
5-ton system$10,400 – $15,800

Ranges reflect typical Arlington single-family homes. Ductwork replacement, electrical upgrades, and code-required updates on older homes are extra and should be itemized in any quote.

Permits in Arlington

Arlington requires a mechanical permit for HVAC system replacement, as do most Dallas–Fort Worth cities. Your installer normally pulls the permit and includes the fee in the quote. In Texas, HVAC contractors are licensed by the state (TDLR), and your contractor should also be registered with the city. Ask to see the permit number on your contract — a contractor who suggests skipping it is a red flag, and an unpermitted install can complicate a future home sale or insurance claim.

Utility incentives in Arlington: the Oncor program

Arlington homes get their electricity delivered by Oncor (you pick a retail electric provider; Oncor runs the wires). Oncor's Home Energy Efficiency program pays an incentive on qualifying high-efficiency AC and heat pump replacements — but the mechanics surprise people:

Gas furnace bonus: most Arlington homes heat with gas from Atmos Energy. Atmos Mid-Tex pays $300 back on an ENERGY STAR gas furnace rated 90% AFUE or higher, or $350 at 95% AFUE and up — worth claiming when you replace the furnace with the AC.

Note: the federal Energy Efficient Home Improvement Credit (Section 25C) ended for equipment installed after December 31, 2025, so don't let a quote count it as a 2026 saving.

Electricity rates: why efficiency pays in Arlington

Texas electricity is deregulated in Oncor territory, so your rate depends on the retail plan you choose — typical all-in residential rates in the Dallas area run roughly 14–17¢ per kWh, with advertised plans ranging much wider (always compare at your real usage on the plan's Electricity Facts Label, via the state's Power to Choose site). Air conditioning is the largest single load in an Arlington home and can approach half of a summer bill, and North Texas systems run eight to nine months a year — so the efficiency tier you pick shows up on bills for the next 12–17 years.

Sizing a system for North Texas heat and humidity

Dallas-area design temperatures sit around 100°F, and Gulf humidity means a system also has to remove moisture, not just heat. An oversized unit short-cycles and leaves the house clammy; an undersized one runs flat-out through August. Don't just match the old nameplate: ask for a Manual J load calculation, and on an older Arlington home have the contractor inspect duct leakage and insulation while the attic is open — sealing ducts on a typical ranch home is one of the cheapest comfort upgrades there is.

The working rule of thumb in North Texas is 1 ton per 500–600 sq ft for typical construction. Use our cost calculator for a first estimate, then insist your installer confirms sizing with a Manual J load calculation. Also note the federal floor: new split systems installed in Texas must be at least 14.3 SEER2 (13.8 SEER2 for systems 45,000 BTU and larger), and split heat pumps at least 14.3 SEER2.

Arlington HVAC replacement FAQ

How much does it cost to replace an AC unit in Arlington, TX?

Most Arlington homeowners pay $8,000–$13,900 installed for a full AC and furnace or heat pump replacement, depending on tonnage and efficiency. A 3-ton standard-efficiency split system typically lands around $8,000–$12,100; larger or high-efficiency systems cost more.

Does Arlington require a permit to replace an AC unit?

Yes. Like most Dallas–Fort Worth cities, Arlington requires a mechanical permit for HVAC replacement. Your TDLR-licensed contractor normally pulls it and includes the fee in the quote — ask for the permit number on your contract.

Can I get an Oncor rebate in Arlington?

Arlington is Oncor territory, and Oncor's Home Energy Efficiency program pays an incentive on qualifying high-efficiency replacements — but it pays your participating contractor, not you directly, and the contractor applies it as a discount. Ask before you sign whether your contractor participates and get the incentive shown as a line item on the quote.

How long should an AC system last in Arlington?

Plan on roughly 12–17 years in North Texas, a bit less than milder parts of the country, because systems here run eight to nine months a year and rack up run-hours fast. If your system is past 12 years and needs a major repair — a compressor or coil, for example — replacement usually beats repair on total cost.

Compare costs in nearby cities

See our other Dallas–Fort Worth guides: Plano, Frisco, Irving, Garland. Or go back to the national cost overview.

Get free quotes from Arlington installers

Tell us about your project and local HVAC partners will contact you with itemized quotes. No obligation.

Prefer email? Write to us at [email protected].